 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz 9 AMPLIFIERS - CONNECTORIZED MODULES Features P1dB Output Power: 10 Watts Gain: 40 dB Output IP3: +54 dBm Single Positive Supply: +12V Thermally Compensated and Protected TTL DC Power Enable Unconditionally Stable Heat Sink/Fan Accessories Available Typical Applications The HMC-C012 is ideal for: * Cellular/3G Infrastructure * Automated Test Equipment (ATE) * Laboratory Use Functional Diagram General Description The HMC-C012 is a 10 Watt Power Amplifier Module suitable for Cellular/3G repeaters, wireless data, laboratory use and ATE applications. This extremely robust PA module is DC blocked, internally regulated and over voltage protected. Thermal protection/fault circuitry automatically turns off DC power if base temperature exceeds +75 C and restores power at < +55 C. Electrical Specifications, TA = +25 C, VIN = +12V Parameter Frequency Range Gain Input Return Loss Output Return Loss Output Power for 1 dB Compression (P1dB) Saturated Output Power (Psat) Output Third Order Intercept (IP3) (Two-tone Input Power = -28 dBm each tone) Channel Output Power for -60 dBc ACPR (CDMA-2000, 1.98 MHz offset) Channel Output Power for -50 dBc ACPR (CDMA-2000, 885 kHz offset) Second Harmonic at Output P1dB Third Harmonic at Output P1dB Spurious at Output P1dB Supply Current 38 9.5 7.5 9 Min. Typ. 0.4 - 1.0 40 12 12 10 42 54 36 34 -20 -30 -65 6.5 7.0 Max. Units GHz dB dB dB W dBm dBm dBm dBm dBc dBc dBc A 9 - 26 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz Gain vs. Temperature 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 0.3 Output IP3 vs. Temperature 60 58 56 54 OIP3 (dBm) 52 50 48 46 +25 C +50 C 0C +25 C +50 C 0C 9 AMPLIFIERS - CONNECTORIZED MODULES 9 - 27 GAIN (dB) 44 42 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 40 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) P1dB vs. Temperature 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 0.3 Psat vs. Temperature 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 0.3 P1dB (dBm) +25 C +50 C 0C Psat (dBm) +25 C +50 C 0C 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) ACPR, CDMA-2000, 1.98 MHz Offset -40 400 MHz 800 MHz 900 MHz 1000 MHz ACPR, CDMA-2000, 885 kHz Offset -30 400 MHz 800 MHz 900 MHz 1000 MHz CDMA2000 Rev. 8 Adjacent Channel Offset: 885 kHz Integration BW: 1.228 MHz Forward Link, SRI, 9 Channels -50 ACPR (dBc) -40 ACPR (dBc) 32 34 36 -60 CDMA2000 Rev. 8 Adjacent Channel Offset: 1.98 MHz Integration BW: 1.228 MHz Forward Link, SRI, 9 Channels -50 -70 -60 -80 -70 -90 24 26 28 30 CHANNEL OUTPUT POWER (dBm) -80 24 26 28 30 32 34 36 CHANNEL OUTPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz 9 AMPLIFIERS - CONNECTORIZED MODULES Input Return Loss vs. Temperature 0 +25 C +50 C 0C Output Return Loss vs. Temperature 0 +25 C +50 C 0C -5 RETURN LOSS (dB) -5 RETURN LOSS (dB) -10 -10 -15 -15 -20 -20 -25 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 -25 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) Reverse Isolation vs. Temperature 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 -70 0.3 Noise Figure vs. Temperature 20 18 16 NOISE FIGURE (dB) +25 C +50 C 0C 14 12 10 8 6 4 2 +25 C +50 C 0C 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 0 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) Absolute Maximum Ratings Supply Voltage (VIN) RF Input Power (RFIN) Storage Temperature Operating Temperature Thermal Fault Indicator Max Pdiss (derate 1.8 mW/C above 50 C) Enable +13 Vdc +10 dBm -40 to +85 C 0 to +50 C 180 mW -0.5 to +6.0 Vdc Thermal Fault Indicator Characteristics Parameter IOUT (VOUT > 2V) RON (I OUT = 50 mA) ROFF (VOUT = 30 V) 1 Min. Typ. 350 7.5 Max. Units mA Ohms MOhm Enable Input Characteristics Parameter Min. 3.5 1.6 -0.5 < 50 Typ. Max. Units V V mA A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS VIH VIL IIL @ VIN = 0V IIH @ 5V 9 - 28 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz Recommended Biasing Procedure TURN-ON 1. Connect RF input and output 2. Apply Supply Voltage VIN (+12 Vdc) 3. Set Enable low 4. Apply RF input signal TURN-OFF 1. Remove RF input signal 2. Remove Supply Voltage VIN 9 AMPLIFIERS - CONNECTORIZED MODULES 9 - 29 Pin Descriptions Pin Number Function Description Interface Schematic 1 RFIN & RF Ground RF input connector, SMA female. This pin is AC coupled and matched to 50 Ohms from 400 - 1000 MHz. 2 VIN Power supply voltage for the amplifier. 3 GND Power supply ground. 4 RFOUT & RF Ground RF output connector, SMA female. This pin is AC coupled and matched to 50 Ohms from 400 - 1000 MHz. 5 GND Ground for thermal fault indicator and enable circuit. 6 Thermal Fault Indicator Open drain output. High impedance for base plate temperatures less than 55 C. Low impedance for base plate temperatures exceeding 75 C. TTL compatible supply voltage (VIN) shutdown. If enable feature is not required, short this pin to DC ground. 7 Enable TTL "High" Disable TTL "Low" Enable For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz 9 AMPLIFIERS - CONNECTORIZED MODULES Outline Drawing NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH a. COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 b. BASE, TIN 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X.1 (2.54mm) .XX.02 (0.50mm) 6. DRAWING TO CHANGE AS REQUIRED. 7. BASE MUST BE GROUNDED AND MOUNTED TO HEAT SINK CAPABLE OF DISSIPATING 100W (65 C) 9 - 30 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-C012 v01.1205 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz HMC-C012 Heatsink/Fan Outline Drawing 9 AMPLIFIERS - CONNECTORIZED MODULES 9 - 31 NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH: COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X.1 (2.54mm) .XX.02 (0.50mm) HMC-C008 Ordering Information Part Number HMC-C012 HMC-C012HV115 HMC-C012HV230 Description 10 Watt Power Amplifier Module, 400 - 1000 MHz 10 Watt Power Amplifier Module with heat sink, 115 Vac fan and power cord. 10 Watt Power Amplifier Module with heat sink, 230 Vac fan and power cord. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com |
Price & Availability of HMC-C012
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |